Hardware Recommendations¶
Ceph was designed to run on commodity hardware, which makes building and maintaining petabyte-scale data clusters economically feasible. When planning out your cluster hardware, you will need to balance a number of considerations, including failure domains and potential performance issues. Hardware planning should include distributing Ceph daemons and other processes that use Ceph across many hosts. Generally, we recommend running Ceph daemons of a specific type on a host configured for that type of daemon. We recommend using other hosts for processes that utilize your data cluster (e.g., OpenStack, CloudStack, etc).
Tip
Check out the Ceph blog too.
CPU¶
Ceph metadata servers dynamically redistribute their load, which is CPU intensive. So your metadata servers should have significant processing power (e.g., quad core or better CPUs). Ceph OSDs run the RADOS service, calculate data placement with CRUSH, replicate data, and maintain their own copy of the cluster map. Therefore, OSDs should have a reasonable amount of processing power (e.g., dual core processors). Monitors simply maintain a master copy of the cluster map, so they are not CPU intensive. You must also consider whether the host machine will run CPU-intensive processes in addition to Ceph daemons. For example, if your hosts will run computing VMs (e.g., OpenStack Nova), you will need to ensure that these other processes leave sufficient processing power for Ceph daemons. We recommend running additional CPU-intensive processes on separate hosts.
RAM¶
Generally, more RAM is better.
Monitors and managers (ceph-mon and ceph-mgr)¶
Monitor and manager daemon memory usage generally scales with the size of the
cluster. For small clusters, 1-2 GB is generally sufficient. For
large clusters, you should provide more (5-10 GB). You may also want
to consider tuning settings like mon_osd_cache_size or
rocksdb_cache_size.
Metadata servers (ceph-mds)¶
The metadata daemon memory utilization depends on how much memory its cache is
configured to consume. We recommend 1 GB as a minimum for most systems. See
mds_cache_memory.
OSDs (ceph-osd)¶
Memory¶
Bluestore uses its own memory to cache data rather than relying on the operating system’s page cache. In Bluestore you can adjust the amount of memory that the OSD attempts to consume by changing the osd_memory_target configuration option.
Setting the osd_memory_target below 2GB is typically not recommended (Ceph may fail to keep the memory consumption under 2GB and this may cause extremely slow performance).
Setting the memory target between 2GB and 4GB typically works but may result in degraded performance as metadata may be read from disk during IO unless the active data set is relatively small.
4GB is the current default osd_memory_target size. This default was chosen for typical use cases, and is intended to balance memory requirements and OSD performance.
Setting the osd_memory_target higher than 4GB can improve performance when there many (small) objects or when large (256GB/OSD or more) data sets are processed.
Important
The OSD memory autotuning is “best effort”. While the OSD may unmap memory to allow the kernel to reclaim it, there is no guarantee that the kernel will actually reclaim freed memory within a specific time frame. This applies especially in older versions of Ceph, where transparent huge pages can prevent the kernel from reclaiming memory that was freed from fragmented huge pages. Modern versions of Ceph disable transparent huge pages at the application level to avoid this, though that still does not guarantee that the kernel will immediately reclaim unmapped memory. The OSD may still at times exceed it’s memory target. We recommend budgeting around 20% extra memory on your system to prevent OSDs from going OOM during temporary spikes or due to any delay in reclaiming freed pages by the kernel. That value may be more or less than needed depending on the exact configuration of the system.
When using the legacy FileStore back end, the page cache is used for caching data, so no tuning is normally needed. When using the legacy FileStore backend, the OSD memory consumption is related to the number of PGs per daemon in the system.
Data Storage¶
Plan your data storage configuration carefully. There are significant cost and performance tradeoffs to consider when planning for data storage. Simultaneous OS operations, and simultaneous request for read and write operations from multiple daemons against a single drive can slow performance considerably.
Important
Since Ceph has to write all data to the journal before it can send an ACK (for XFS at least), having the journal and OSD performance in balance is really important!
Hard Disk Drives¶
OSDs should have plenty of hard disk drive space for object data. We recommend a minimum hard disk drive size of 1 terabyte. Consider the cost-per-gigabyte advantage of larger disks. We recommend dividing the price of the hard disk drive by the number of gigabytes to arrive at a cost per gigabyte, because larger drives may have a significant impact on the cost-per-gigabyte. For example, a 1 terabyte hard disk priced at $75.00 has a cost of $0.07 per gigabyte (i.e., $75 / 1024 = 0.0732). By contrast, a 3 terabyte hard disk priced at $150.00 has a cost of $0.05 per gigabyte (i.e., $150 / 3072 = 0.0488). In the foregoing example, using the 1 terabyte disks would generally increase the cost per gigabyte by 40%–rendering your cluster substantially less cost efficient.
Tip
Running multiple OSDs on a single disk–irrespective of partitions–is NOT a good idea.
Tip
Running an OSD and a monitor or a metadata server on a single disk–irrespective of partitions–is NOT a good idea either.
Storage drives are subject to limitations on seek time, access time, read and write times, as well as total throughput. These physical limitations affect overall system performance–especially during recovery. We recommend using a dedicated drive for the operating system and software, and one drive for each Ceph OSD Daemon you run on the host. Most “slow OSD” issues arise due to running an operating system, multiple OSDs, and/or multiple journals on the same drive. Since the cost of troubleshooting performance issues on a small cluster likely exceeds the cost of the extra disk drives, you can optimize your cluster design planning by avoiding the temptation to overtax the OSD storage drives.
You may run multiple Ceph OSD Daemons per hard disk drive, but this will likely lead to resource contention and diminish the overall throughput. You may store a journal and object data on the same drive, but this may increase the time it takes to journal a write and ACK to the client. Ceph must write to the journal before it can ACK the write.
Ceph best practices dictate that you should run operating systems, OSD data and OSD journals on separate drives.
Solid State Drives¶
One opportunity for performance improvement is to use solid-state drives (SSDs) to reduce random access time and read latency while accelerating throughput. SSDs often cost more than 10x as much per gigabyte when compared to a hard disk drive, but SSDs often exhibit access times that are at least 100x faster than a hard disk drive.
SSDs do not have moving mechanical parts so they are not necessarily subject to the same types of limitations as hard disk drives. SSDs do have significant limitations though. When evaluating SSDs, it is important to consider the performance of sequential reads and writes. An SSD that has 400MB/s sequential write throughput may have much better performance than an SSD with 120MB/s of sequential write throughput when storing multiple journals for multiple OSDs.
Important
We recommend exploring the use of SSDs to improve performance. However, before making a significant investment in SSDs, we strongly recommend both reviewing the performance metrics of an SSD and testing the SSD in a test configuration to gauge performance.
Since SSDs have no moving mechanical parts, it makes sense to use them in the areas of Ceph that do not use a lot of storage space (e.g., journals). Relatively inexpensive SSDs may appeal to your sense of economy. Use caution. Acceptable IOPS are not enough when selecting an SSD for use with Ceph. There are a few important performance considerations for journals and SSDs:
Write-intensive semantics: Journaling involves write-intensive semantics, so you should ensure that the SSD you choose to deploy will perform equal to or better than a hard disk drive when writing data. Inexpensive SSDs may introduce write latency even as they accelerate access time, because sometimes high performance hard drives can write as fast or faster than some of the more economical SSDs available on the market!
Sequential Writes: When you store multiple journals on an SSD you must consider the sequential write limitations of the SSD too, since they may be handling requests to write to multiple OSD journals simultaneously.
Partition Alignment: A common problem with SSD performance is that people like to partition drives as a best practice, but they often overlook proper partition alignment with SSDs, which can cause SSDs to transfer data much more slowly. Ensure that SSD partitions are properly aligned.
While SSDs are cost prohibitive for object storage, OSDs may see a significant
performance improvement by storing an OSD’s journal on an SSD and the OSD’s
object data on a separate hard disk drive. The osd journal configuration
setting defaults to /var/lib/ceph/osd/$cluster-$id/journal. You can mount
this path to an SSD or to an SSD partition so that it is not merely a file on
the same disk as the object data.
One way Ceph accelerates CephFS file system performance is to segregate the
storage of CephFS metadata from the storage of the CephFS file contents. Ceph
provides a default metadata pool for CephFS metadata. You will never have to
create a pool for CephFS metadata, but you can create a CRUSH map hierarchy for
your CephFS metadata pool that points only to a host’s SSD storage media. See
Mapping Pools to Different Types of OSDs for details.
Controllers¶
Disk controllers also have a significant impact on write throughput. Carefully, consider your selection of disk controllers to ensure that they do not create a performance bottleneck.
Tip
The Ceph blog is often an excellent source of information on Ceph performance issues. See Ceph Write Throughput 1 and Ceph Write Throughput 2 for additional details.
Additional Considerations¶
You may run multiple OSDs per host, but you should ensure that the sum of the
total throughput of your OSD hard disks doesn’t exceed the network bandwidth
required to service a client’s need to read or write data. You should also
consider what percentage of the overall data the cluster stores on each host. If
the percentage on a particular host is large and the host fails, it can lead to
problems such as exceeding the full ratio, which causes Ceph to halt
operations as a safety precaution that prevents data loss.
When you run multiple OSDs per host, you also need to ensure that the kernel
is up to date. See OS Recommendations for notes on glibc and
syncfs(2) to ensure that your hardware performs as expected when running
multiple OSDs per host.
Networks¶
Consider starting with a 10Gbps+ network in your racks. Replicating 1TB of data
across a 1Gbps network takes 3 hours, and 10TBs takes 30 hours! By contrast,
with a 10Gbps network, the replication times would be 20 minutes and 1 hour
respectively. In a petabyte-scale cluster, failure of an OSD disk should be an
expectation, not an exception. System administrators will appreciate PGs
recovering from a degraded state to an active + clean state as rapidly
as possible, with price / performance tradeoffs taken into consideration.
Additionally, some deployment tools employ VLANs to make hardware and network
cabling more manageable. VLANs using 802.1q protocol require VLAN-capable NICs
and Switches. The added hardware expense may be offset by the operational cost
savings for network setup and maintenance. When using VLANs to handle VM
traffic between the cluster and compute stacks (e.g., OpenStack, CloudStack,
etc.), it is also worth considering using 10G Ethernet. Top-of-rack routers for
each network also need to be able to communicate with spine routers that have
even faster throughput–e.g., 40Gbps to 100Gbps.
Your server hardware should have a Baseboard Management Controller (BMC). Administration and deployment tools may also use BMCs extensively, so consider the cost/benefit tradeoff of an out-of-band network for administration. Hypervisor SSH access, VM image uploads, OS image installs, management sockets, etc. can impose significant loads on a network. Running three networks may seem like overkill, but each traffic path represents a potential capacity, throughput and/or performance bottleneck that you should carefully consider before deploying a large scale data cluster.
Failure Domains¶
A failure domain is any failure that prevents access to one or more OSDs. That could be a stopped daemon on a host; a hard disk failure, an OS crash, a malfunctioning NIC, a failed power supply, a network outage, a power outage, and so forth. When planning out your hardware needs, you must balance the temptation to reduce costs by placing too many responsibilities into too few failure domains, and the added costs of isolating every potential failure domain.
Minimum Hardware Recommendations¶
Ceph can run on inexpensive commodity hardware. Small production clusters and development clusters can run successfully with modest hardware.
Process |
Criteria |
Minimum Recommended |
|---|---|---|
|
Processor |
|
RAM |
|
|
Volume Storage |
1x storage drive per daemon |
|
DB/WAL |
1x SSD partition per daemon (optional) |
|
Network |
1x 1GbE+ NICs (10GbE+ recommended) |
|
|
Processor |
|
RAM |
2GB+ per daemon |
|
Disk Space |
10 GB per daemon |
|
Network |
1x 1GbE+ NICs |
|
|
Processor |
|
RAM |
2GB+ per daemon |
|
Disk Space |
1 MB per daemon |
|
Network |
1x 1GbE+ NICs |
Tip
If you are running an OSD with a single disk, create a partition for your volume storage that is separate from the partition containing the OS. Generally, we recommend separate disks for the OS and the volume storage.
